Monday, January 21, 2013, A101, 1st Floor, WNLO
SESSION 1, 09:00 to 10:30, Chair: Prof. Xinliang Zhang(张新亮)
09:00-09:15 OEDI 2013 Annual Meeting Opening Ceremony
09:15-09:45 [OEDI-1](Invited),唐江
Abstract:
09:45-10:15 [OEDI-2](Invited),Hybrid long-range surface plasmon polariton waveguides,陈林
10:15-10:30 [OEDI-3] Photonic Generation of UWB Pulses by Using Fabry-Pérot Semiconductor Optical Amplifier,于源
Abstract:
10:30-11:00 Coffee/Tea Break
SESSION 2, 11:00 to 12:00, Chair: Prof. Jiang Tang(唐江)
11:00-11:30 [OEDI-4](Invited),Demodulation and MIMO Equalization for Mode Division Multiplexing System using a Novel Few-mode fiber,付松年
Abstract:
11:30-11:45 [OEDI-5] Low Cost Wide-gap Polarization Mode Converter with Segmented Waveguide Taper,汪灵杰
Abstract:
A new type of low cost polarization mode converter on basis of the segmented waveguide taper (SWT) has been proposed, which can reduce the excess loss drastically from 5dB to less than 1.5dB.
11:45-12:00 [OEDI-6] A novel multi-OAM-mode multi-ring fiber for space-division multiplexing,李树辉
Abstract:
We propose a multi-ring fiber consisting of 7 rings each supporting 12 degenerate orbital angular momentum (OAM) modes for high density space-division multiplexing (SDM). Large effective refractive index (neff) differences of OAM modes have been designed to suppress the inter-mode crosstalk. The minimum neff difference achieves an order of 10-4 for a wide bandwidth. We evaluate the inter-ring crosstalks of the OAM modes guided by the MRF through a coupled-mode theory. The simulation results indicate that except two highest order of OAM modes which can be discard in practical applications, the inter-ring crosstalks of the rest are below -40 dB with the propagation length of 100 km, 60nm bandwidth and a small ring-to-ring distance of 28μm.
12:00-14:00 Lunch Break
Monday, January 21, 2013, A101, 1st Floor, WNLO
SESSION 3, 14:00 to 15:30 Chair: Prof. Junqiang Sun(孙军强)
14:00-14:30 [OEDI-7](Invited),唐明
Abstract:
14:30-15:00 [OEDI-8](Invited),多进制高速光计算,王健
Abstract:
15:00-15:15 [OEDI-9] Controllable amplification, absorption, and dispersion in double- cascade type four-level system of multiple quantum wells,严伟
Abstract:
A double-cascade type four-level system of semiconductor multiple quantum wells (MQWs) was constructed with biexcitons and excitons. The nonlinear optical properties for amplification, absorption, and dispersion of two weak fields in this scheme are investigated. It shows that the amplification, absorption, and dispersion responses of two weak fields can be achieved by adjusting the relative phase, the probe detuning, and the two control Rabi frequencies appropriately. The investigation is much more practical than its atomic counterpart because of its flexible design and the wide adjustable parameters. It may provide a new possibility in technological applications for the light amplifier and optical switch working on quantum coherence effects in MQWs solid-state system.
15:15-15:30 [OEDI-10] Simple and stable optical frequency comb generation used for arbitrary waveform generation,杨婷
Abstract:
We demonstrate stable optical frequency comb based on cascaded modulators and highly nonlinear fiber. Assisted by optical pulse shaping, several different high-fidelity arbitrary waveforms, such as cosine, rectangle, triangle, and half-wave cosine signals are obtained.
15:30-16:00 Coffee/Tea Break
Monday, January 21, 2013, A101, 1st Floor, WNLO
SESSION 4, 16:00 to 17:30, Chair: Prof. Ming Tang(唐明)
16:00-16:30 [OEDI-11](Invited),Our recent research on fiber resonance sensing,夏历
16:30-16:45 [OEDI-12] Photonic Generation of Ultra-wideband Signals based on an In-line Microfiber Mach-Zehnder Interferometer,赵平
Abstract:
We present and demonstrate the photonic generation of ultra-wideband (UWB) signals based on an in-line polarization-dependent microfiber Mach-Zehnder interferometer and a phase modulator. Polarity-switchable doublet pulses with with a central frequency of 6.28 GHz and a 10-dB bandwidth of 7. 86 GHz are successfully obtained.
16:45-17:00 [OEDI-13] A Novel Fiber Nonlinearity Suppression Method in DWDM Optical Fiber Transmission Systems with an All-optical Pre-distortion Module,成浩然
Abstract:
We propose a novel all-optical scheme to mitigate fiber nonlinearities in DWDM transmission line by applying time-domain fractional Fourier transform (FRFT) to pre-distort transmitted signals. Simulation results show that the received BER is improved by several orders of magnitude for a 40Gbit/s CSRZ-OOK DWDM system.
17:00-17:15 [OEDI-14] Temporal filter for signal processing,吴朝
Abstract:
We propose and demonstrate a scheme for format conversion and pulse compression using time lens. Analog to the well-known 4-f spatial processor, a temporal filter is added to this system exactly in the joint focal plane. The NRZ to RZ format conversion and pulse compression are realized by the delay interferometer and micro ring resonator, respectively.
17:15-17:30 [OEDI-15] Observation of Similar Spectral Hole Burning Effect in EDFAs,陈国栋
Abstract:
A novel similar spectral hole burning (SSHB), totally different from the common spectral hole burning (SHB) effect, is observed during multiwavelength amplification. Experimental results indicate that the burning hole position of SSHB keeps unchangeable regardless of the variations of the strong signal wavelength, whereas the burning hole depth is dependent on signal wavelength and power. In designing gain-flattened erbium-doped fiber amplifiers (EDFAs), SSHB effect cannot be ignored due to its dynamic impact on the property of gain spectrum.
Tuesday, January 22, 2013, A101, 1st Floor, WNLO
SESSION 5, 09:00 to 10:15, Chair: Prof. Jianji Dong(董建绩)
09:00-09:30 [OEDI-16](Invited),三维螺旋人工超材料的研究进展,杨振宇
Abstract:
09:30-09:45 [OEDI-17] Some Novel Optical Devices Based on Vertical Slot Structure on Silicon-on-Insulator,黄增智
Abstract:
Vertical slot waveguide is fabricated by electron beam lithography (EBL) and inductively coupled plasma (ICP) etch processes. A ring resonator is formed by the vertical slot waveguide. The slot ring resonator has a high quality factor of 40000. Based on the vertical slot structure, two novel optical devices are proposed. A ridge slot waveguide can promote the optical confinement factor of the vertical slot waveguide, which is of potential use of light amplification and producing high nonlinearity. An asymmetric slot directional coupler is intended to decrease the coupling length of the slot directional coupler, thus making the device more compact.
09:45-10:00 [OEDI-18],Photonic crystal nanocavity: design, fabrication and applications,张永
Abstract:
We designed and fabricated high-Q photonic crystal nanocavity (Q~150000) by e-beam lithography and ICP. We also investigated the characteristics of the high-Q photonic crystal nanocavity at various input powers. Nonlinear cavity characteristics were observed at an ultra-low input power of 4.65W, which was much lower than the previously reported value in similar 2D silicon photonic crystal nanocavity. Nonlinear coupled-mode theory was used to analyze the nonlinear characteristics and optical bistability in our nanocavity. We confirmed that these ultra-low power nonlinear optical effects could be attributed to the high-Q factor and large effective thermal resistance of our nanocavity. Finally, a significant enhancement of photoluminescence and a resonant peak with quality factor of 4000 at 1.524mwas observed from photonic crystal nanocavity containing Ge self-assembled quantum dots on silicon-on-insulator substates.
10:00-10:15 [OEDI-19],Proposal for all-optical half-adder and half-subtracter based on twin four-wave mixing in a single slot waveguide,桂成程
Abstract:
A simple scheme of half-adder and half-subtracter at 160 Gbit/s is proposed and numerically simulated based on twin four-wave mixing (FWM) using a single silicon slot waveguide. By appropriately optimizing the input signal power and the waveguide length, half-adder and half-subtracter can be realized. The operation performance is calculated and discussed, including eye diagrams, eye opening (EO), extinction ratio (ER) and quality-factor (Q-factor). A theoretical basis for obtaining optimal operation performance for half-adder and half-subtracter is provided by optimizing the input signal power and the waveguide length.
10:15-10:45 Coffee/Tea Break
SESSION 6, 10:45 to 11:50, Chair: Prof. Jian Wang (王健)
10:45-11:15 [OEDI-20](Invited),汪毅
11:15-11:30 [OEDI-21] Single-etched high-Q SOI microring resonator integrated with efficient grating couplers,李丹萍
Abstract:
We demonstrate a single-etched high-Q, high ER SOI microring resonator which integrated with efficient grating couplers using a combination of EBL and ICP-RIE. 40nm 3-dB bandwidth and 40% coupling efficiency are experimentally realized. An ER of 19 dB and Q factor of ~55,000 are achieved for a 40μm radius ring.
11:30-11:45 [OEDI-22] The growth of large period germanium quantum dots and the precisely embedding single quantum dot into a nano cavity,曾成
Abstract:
The lateral ordering of GeSi quantum dots on patterned Si (001) with 3μm period using solid source molecular beam epitaxy has beem demonstrated. A photoluminescence (PL) peak at 0.82 eV from this large period ordered QDs was observed at 17K. This large period ordered GeSi QDs make the incorporation of single QD into nano cavity become possible. In order to embed single dot into a nano cavity, a 3.4μm deep topographical marker on SOI is made by Lithography and ICP etcher. The overlay accuracy is less than 25nm.
11:45-14:00 Lunch Break
Tuesday, January 22, 2013, A101, 1st Floor, WNLO
SESSION 7, 14:00 to 15:00, Chair: Prof. Yu YU(余宇)
14:00-14:15 [OEDI-23] Widely tunable lasers based on digital concatenated grating with multiple phase shifts,赵家霖
Abstract:
In this paper, we proposed a monolithic four-section widely tunable semiconductor laser based on digital concatenated grating with multiple phase shifts (MPS-DCG). The MPS-DCG provides a comb-like reflection spectrum with flat envelop covering large wavelength range. Static characteristics of the MPS-DCG laser including the tuning curves and P-I curves are simulated using the time-domain traveling wave model combined with the digital filter method. Tuning range of approximately 88nm has been demonstrated theoretically.
14:15-14:30 [OEDI-24] Impact of Al0.3Ga0.7As interlayer thickness on quality of GaAs on Ge substrate grown by metalorganic vapor deposition,李森林
Abstract:
GaAs/Al0.3Ga0.7As/Ge heterostructures with varying Al0.3Ga0.7As interlayer thickness have been investigated. It was found that the Al0.3Ga0.7As inserting layer in the GaAs/Ge interface could eliminate the anti-phase domains (APDs) and suppress the Ge atoms interdiffusion efficiently. In addition, we also showed that the best morphology and crystalline quality of GaAs was obtained with Al0.3Ga0.7As inserting layer thickness ranged from 15nm to 23nm.
14:30-14:45 [OEDI-25] Design of a Hybrid Slot Plasmonic Waveguide with Nanoscale Light Confinement and Its Application for Ultrafast All-Optical Switching,张仲来
Abstract:
We design a novel hybrid slot plasmonic waveguide with a long propagation length of 1020 µm and a small effective mode area of 6.4×10-2µm2. We simulate and achieve ultrafast all-optical switching using non-degenerate FWM in the waveguide.
JOINT POSTER SESSION, 14:45 to 17:30, Lobby, 1st Floor, WNLO
POSTER 统一张贴时间和地点: 11:50-14:00, Lobby, 1st Floor, WNLO
Annual OEDI Banquet, 18:00, 地点待定
JOINT POSTER SESSION, 14:45 to 17:30,Lobby, 1st Floor, WNLO
[OEDI-P-01] 张文甲,Modeling of optical configuration of tunable external-cavity diode lasers with Zemax
Abstract:
In this paper, a method to model the optical cavity of tunable external-cavity diode lasers by Zemax is proposed. Models of external optical cavity of Littrow and Littman-Metcalf configurations are built. And optimizations are performed to maximize the coupling efficiency of the external feedback. Analyses of the models are discussed and by programming a Zemax macro, the feedback coupling and the tuning curves are achieved. With the simulations, we propose a tuning method which uses a rotating collimating lens. This tuning method has been demonstrated by experiments.
[OEDI-P-02] 石隅,Low Power CW Pump Wavelength Conversion in a Silicon Microring Resonator
Abstract:
In this report we demonstrate wavelength conversion via four wave mixing (FWM) effect using 10 milliwatts CW pump power in the silicon microring resonator, which may lay a solid foundation in future applications like quantum information and high speed optical signal processing.
[OEDI-P-03] 张强,Realizing of a 80。Vertical Angle with MRIE in Etching of the Silica Mask Deposited in InP Substrate
Abstract:
The etching parameters for the silica mask deposited in InP substrate in our micro-nano fabrication platform is investigated. The experimental results show that a
80。vertical angle of silica waveguide can be obtained by MRIE with a parameters of 70 sccm CHF3, 1 sccm O2, and 80 W RF power. With these parameters, a microring with a 86.8。 vertical angle and a radius of 500 μm is obtained in InP substrate with ICP though the silica mask vertical angle utilizing the parameters for realizing 80。vertical angle is only 70。
due to the unstable characteristic of MRIE in our laboratory.
[OEDI-P-04]郁春潮,Slow light between two absorbing resonance in asymmetry double quantum dots
Abstract:
We proposed a slow light in the double resonance asymmetry QDs systems.with enhanced bandwith and compact dimension, compatible for the optical communication.
[OEDI-P-05] 杜鸣笛,Impact of groove defect depth in subwavelength metal grating on THz spoof SPPs
Abstract:
We proposed a groove defect depth effect THz spoof SPPs with better confined THz electric field distribution, which can be applied in THz frequency attenuator.
[OEDI-P-06] 张进,A new method for GaN / AlN quantum dots with uniform size in MOCVD
Abstract: We first time to fabricate GaN QDs via thermal decomposition of GaN film in H2 atmosphere. The obtained GaN QDs has a great quality and uniform size distribution.
[OEDI-P-07] 陈开胜,Cl2/CH4/H2-Inductively Coupled Plasma Etching of InP with Low Electrode Temperature
Abstract:
We are developing a dry-etching process of InP material with vertical and smooth sidewalls and Low electrode temperature.
[OEDI-P-08] 陈鑫,Application of Multi-mask on Clearing the UV- Nanoimprint
Lithography Residual Resist
Abstract:
UV-Nanoimprint Lithography(NIL) has been widely used in manufacturing gratings of Distributed Feedback Laser Diodes(DFB LDs) due to its high-resolution and low cost .However, UV-curable resist turns into high polymer after UV-exposure, which always can’t be eliminated completely, and the residual resist will affect following process and degrade devices performance. In this paper, a Multi-mask layer process to eliminate residual resist was demonstrated. In this process, a thin hard mask is deposited between wafer and UV-curable resist
[OEDI-P-09] 黄田野,Comparison of nonlinear-based approaches for all-optical clock recovery
We compare two different nonlinear fiber-based approaches for all-optical clock recovery (AOCR) at 40 Gb/s. Both involve mode-locking a semiconductor fiber laser (SFL); one is based on the use of a nonlinear optical loop mirror (NOLM) while the second exploits nonlinear polarization rotation (NPR). We assess the impact of input signal characteristics on the RMS timing jitter and power fluctuation. The results show that both approaches are capable of recovering a good quality clock signal over a large range of operating parameters
[OEDI-P-10]李玉涟,Origin of the redshift of the luminescence peak in InGaN light-emitting diodes exposed to Co-60 γ-ray irradiation
Abstract:
The redshift (~54 meV) of the photoluminescence (PL) peak energy of blue InGaN/GaN LED exposed to 60Co γ-rays was observed. Time-resolved PL (TRPL) shows that the PL radiative time increases along with irradiance. The temperature-dependent PL and photoreflectance techniques show that γ-ray irradiance leads to higher carrier localization energies and larger Stokes’ shift, respectively. These facts suggest that the redshifts of the PL peak emission introduced by γ-ray irradiance mainly originated from the enhancement of indium fluctuation. The cathodoluminescent (CL) images of the samples before and after γ-ray irradiation are compared to verify the results.
[OEDI-P-11] 刘力,Tunable and Reconfigurable Notch Microwave Photonic Filters Using on-chip Cascaded Microring Resonators
Abstract:
We propose and experimentally demonstrate a tunable and reconfigurable notch microwave photonic filter (MPF) using two integrated microring resonators (MRRs) on a single silicon-on-insulator (SOI) chip. The free spectral ranges (FSRs) of
two cascaded MRRs are 160 GHz and 165 GHz, respectively. Due to the vernier effect, the transmission spectrum of cascaded MRRs is a series of bimodal distribution whose interval is an arithmetic sequence. By locating the laser wavelength at the middle of different bimodal interval and fine tuning it properly, both central frequency and bandwidth of the notch MPF can be tunable. In the experiment, the tunability of central frequency and 3-dB bandwidth are demonstrated from 2.5 GHz to 17.5 GHz and from 6 GHz to 9.5 GHz, respectively. The best rejection ratio of the notch filter is larger than 40 dB. This approach will allow the implementation of low-cost, very compact, and integrated notch MPFs in a silicon chip.
[OEDI-P-12]秦毅,A filterless optical microwave generation by using frequency octupling technique
Abstract:
A filterless RoF system with frequency octupling is experimentally demonstrated. Optical microwave signals with 34 dB undesired sideband suppression ratios can be obtained. No penalty is observed after transmission over 50 km single-mode fiber.
[OEDI-P-13]谭斯斯,All-optical Differential Equation Solver Based on Microring Resonator
Abstract:
It is demonstrated that a single microring resonator with specific parameters behaves as an all-optical constant-coefficient
first-order linear ordinary differential equation solver. The output at the drop port of a basic add-drop single microring resonator is proportional to the solution of the equation. Moreover, higher order
linear ordinary differential equations can also be solved simply by cascading these microring resonators. Our simulated results have confirmed the feasibility of this simple approach to solve the equations for different values of the constant-coefficient and two considered input waveforms.
[OEDI-P-14] 熊辉,Effects of the AlN buffer layer thickness on the properties of ZnO films grown on c-sapphire substrate by pulsed laser deposition
Abstract:
In this work, ZnO films with high crystal quality were grown by pulsed laser deposition (PLD) on different c-plane AlN/c-sapphire template thereby the thicknesses of AlN buffer layers varied from 150 to 300 nm. The properties of ZnO thin films were studied by using high-resolution X-ray diffraction, atomic force microscopy, photoluminescence spectroscopy, and Raman measurement. The comparative investigation results show that inserting an AlN buffer layer is an effective way to improve the crystal quality of ZnO films. Furthermore, the thickness of the AlN buffer layer plays an important role on the quality of ZnO films. The result of (0002) x-rocking curve with the full width at half maximum (FWHM) of 0.09°indicates that high-quality c-plane ZnO films can be achieved by using a 150 nm-thickness AlN/c-sapphire template. In the best knowledge of the authors, this is the minimum value reported at present for ZnO films grown on AlN/c-sapphire templates by PLD.
[OEDI-P-15] 王玘,Near-field Microwave Imaging System
Abstract:
The microwave imaging system is based on the newly developed spintronic Michelson interferometer, which can utilize the full coherence of the electromagnetic dynamics to investigate the propagating parameters of microwave in dielectric. By analyzing the phase and amplitude changes of the interference pattern, the dielectric constant measurement and metal detection are achieved.
[OEDI-P-16] 郑傲凌,Multi-functional photonic differentiators based on versatile demodulation of phase signals
Abstract:
We demonstrate a multifunctional differentiator using cascaded delayed interferometers.
[OEDI-P-17] 陈涛,Generation of degenerate entangled photon pairs by cascaded second-order nonlinearity in a single periodically poled LiNbO3 waveguide
Abstract:.
We proposed an entangled photon generation based cSFG/SPDC with highly efficient entangled photon pair generation
[OEDI-P-18] 黄章立,Infrared characteristics of VO2 thin films for smart window and laser protection
Abstract:
We propose and optimize the process parameters to bring down the transition temperature of VO2 films and make it suitable for smart window and laser protection applications.
[OEDI-P-19] 黄钊,A double taper Fabry-Perot cavity optical structure designed for hybrid lasers on SOI integrated circuit
Abstract:
We proposed a novel hybrid laser structure having a III-V taper-shaped rectangular F-P cavity bonded on a Silicon taper-shaped ridge waveguide with opposite taper direction. By operating the phase velocities of the individual waveguides, we can cause the optical power to be confined to each of the two waveguides. This is realized by controlling the geometry parameters of the two waveguides . Optical power is confined in the III-V material to get transmission gain,while in the double-taper area , part of the power is ordered to access into the silicon ridge waveguide as output of the laser,owing to the geometry parameters’ shifty.
[OEDI-P-20] 李小明,Direct and indirect intraband optical absorption due to transitions from discrete levels to continuum states in quantum dot system
Abstract:
We present model to calculate the direct and phonon-assisted intraband optical transition in the framework of the first-order perturbation theory and second-order perturbation theory, respectively.
[ OEDI-P-21] 覃翠,Gain recovery dynamics in SOAs with DFB grating under assist light injection
Abstract:
We proposed the SOAs with DFB grating under assist light injection. Both enhanced the effect of the assist light and shortened carriers recovery time are analyzed.
[OEDI-P-23] 左强,Multiple Phase-Shifted DFB laser Fabricated by Nanoimprint Lithography
Abstract:
Two symmetry λ/8 phase-shifts diffraction grating for DFB laser is mass produced by nanoimprint lithography (NIL). Threshold current of typical laser device is less than 15mA. Side mode suppression ratio (SMSR) is above 42dB even at 100mA current injection. Our results prove NIL is a promising tool for fabricating complex diffraction grating DFB laser.
[OEDI-P-24] 赵建宜,Experimental demonstration of Sixteen-Channel DFB Laser Array based on Nanoimprint Technology
Abstract:
A sixteen-channel monolithically integrated index-coupled distributed-feedback laser array has been fabricated using nanoimprint technology. Selective lasing wavelength with 300 GHz and 100 GHz frequency space are obtained. The fine tenability for individual laser in the array is achieved with a Ti-Au thin-film resistor integrated on the chip. The typical threshold current is between 10 mA and 15 mA without current in the thin-film resistor. The optical output power of each channel is about 6 mW at an injection current of 70 mA.
[OEDI-P-25] 郜雅,A Proposal for All-optical DPSK Precoder Using AlGaAs Microring Resonators
Abstract:
An all-optical DPSK precoder scheme based on AlGaAs microring resonators is proposed and numerically simulated. This scheme mainly utilizes the cross phase modulation (XPM) in microring resonators to obtain phase modulation (PM), and realizes the addition of phase shift through a feedback path consisting of a semiconductor optical amplifier (SOA) and another microring as the time delay element. This novel precoder accomplishes not only phase modulation but also differential encoding simultaneously in optical domain. The phase-interference resistance of 40Gb/s DPSK encoded by this scheme reaches up to 0.4 radians, which shows strong stability and great potential in future integrated all-optical communication.
[OEDI-P-26] 田武,Tunability of intersubband transition wavelength in the atmospheric window in AlGaN/GaN multi-quantum wells grown on different AlGaN templates by MOCVD
Abstract:
The properties of intersubband transition in AlGaN/GaN multi-quantum wells (MQWs) grown on different AlGaN templates by metalorganic chemical vapor deposition are investigated. The strain states of GaN wells are studied by Raman spectra and reciprocal space mappings (RSM), which shows that the GaN wells are compressively strained and the compressive strain is increased when the Al mole composition is varied from 0 to 0.3. The Fourier transform infrared spectrometer (FTIR) results show that the intersubband transition wavelength in the AlGaN/GaN MQWs can be tuned from 5.14 μm to 4.65 μm when the Al mole composition of the AlGaN template is increased. The results can be attributed to the quantum confined Stark effect.
[OEDI-P-27] 向磊,Simultaneous multi-channel RZ-OOK/DPSK to NRZ-OOK/DPSK format conversion based on integrated DI and AWG
Abstract:
We designed and fabricated a Delay Interferometer cascaded with an Arrayed-Waveguide Grating based on Silicon on Insulator. 4-channel Return-to-zero On off keying to Non-return-to-zero On off keying and Return-to-zero Differential Phase shift keying to Non-Return-to zero Differential Phase shift keying format conversions at 40 Gbit/s were realized with this integrated device, the output eye diagrams showed a good conversion performance.
[OEDI-P-28]袁小文,Modulation of Spontaneous Emission in 2D hybrid plasmonic–photonic crystal for the efficient coupling
Abstract:
The spontaneous emission (SE) of colloidal CdSe/ZnS quantum Dots (CQDs) modified by the hybrid plasmonic-photonic crystal is reported in this paper. By using spin coater, the spatial overlap between the CQDs and the surface resonance modes in this quasi-2D crystal slab is achieved. In this case, the coupling efficiency of them is enhanced and most excited CQDs radiate through the same surface mode. Thus, not only the angle emission distribution of SE is modified but also the changes of the average lifetime and the line-width almost reach up to 70%.
[OEDI-P-29] 廖健飞,Ultra-Flattened Chromatic Dispersion and Highly Nonlinear Photonic Crystal Fibers With Ultralow Confinement Loss Employing Hybrid Cladding
Abstract:
In this paper, two new types of dispersion-flattened photonic crystal fibers (DF-PCFs) with highly nonlinear and ultralow confinement loss are proposed. Results show that the ultra-flattened dispersion of 0.931 ps/(nm.km) (DF-PCF1) and 1.533 ps/(nm.km) (DF-PCF2) can be achieved in the wavelength range from 1.3 to 1.6 μm with confinement losses lower than 0.001 dB/km in the same wavelength range. Meanwhile, the nonlinear coefficients of our proposed PCFs are greater than 23.83 W-1km-1 (DF-PCF1) and 29.65 W-1km-1 (DF-PCF2) at the wavelength of 1.55 μm, and two near-zero dispersion values of 0.328 ps/(nm.km) (DF-PCF1) and -0.015 ps/(nm.km) (DF-PCF2) can also be obtained at the same wavelength. Furthermore, the influence of manufacturing imperfections of parameters on dispersion and nonlinearity is discussed to verify the robustness of our design.
[OEDI-P-30] 蒙庆华,Design and Fabrication of Micro F-P Cavity Tunable Filter Array Structure for Hyperspectral Imaging Spectrometer
Abstract:
In this paper, we design and Fabricate of Micro F-P Cavity Tunable Filter Array Structure for Hyperspectral Imaging Spectrometer.
[OEDI-P-31] 江桂英,Improvement of Remodulation Characteristics by Using Two-Section Reflective SOA for Colorless WDM-PON
Abstract:
We investigate the remodulaton characteristics of the two-section RSOA for colorless WDM-PON. By adjusting the currents of the two sections, we can improve the output extinction ratio(ER) and Q factor because it works as modulator, amplifier and equalizer at the same time.
[OEDI-P-32] 陈荟全,Hydrothermal Synthesis of ZnO Nanowires on GaN Quantum Dots
Abstract:
UV LED based on the structure of N-ZnO nanowires(NWs)/P-GaN has been widely studied nowadays. NWs increasing the luminous efficiency. However, in the present research, this sturcture has a big turn-on voltage as high as 3V[1]. We generate ZnO NWs on GaN quantum dots(QDs)/P-GaN. This method is expected to reduce the turn-on voltage of the devices and make the devices keep working stable at the same time.
[OEDI-P-33] 齐志强,A novel AlN buffer layer structure based on the pulsed atomic layer epitaxy to improve the quality of the AlN films
Abstract:
We insert middle temperature PALE layer in high temperature buffer layer which can improve surface morphology and crystalline quality.
[OEDI-P-34] 张芳,Ultrasmall Broad-band Polarizer Based on a metal-insulator-metal Waveguide Bragg Grating
Abstract:
An ultrasmall broad-band polarizer consisting of a dielectric grating sandwiched between two metal films is proposed and the mechanism of polarization-selective transmission is investigated using finite element method (FEM). Figure 1depicts the schematic of the proposed device, the refractive indices of the dielectric materials are chosen to be nH = 3.5 and nL =2.05, d and t stand for the period and thickness of the dielectric grating, respectively. The low-index and high-index dielectric regions are set to be the same, that is, w=w’=d/2.
[OEDI-P-35] 李洋,The effect of SiNx interlayer on Si-Al0.48Ga0.52N grown by MOCVD
Abstract:
Si-doped Al0.48Ga0.52N layers were grown on sapphire (0001) substrates using SiNx interlayer with different treat time. The crystal quality, strain states, surface, electrical and optical properties of four samples were investigated through High Resolution X-ray diffraction, Raman spectra, atomic force microscope, Hall measurement and photoluminescence. The mechanism of SiNx nano-mask in the growth process of n-Al0.48Ga0.52N was analyzed.
[OEDI-P-36] 张伟,Improved Ohmic contacts to plasma etched n-Al0.5Ga0.5N by annealing under nitrogen ambient before metal deposition
Abstract:
We propose an approach to realizing Ohmic contacts to plasma etched n-AlxGa1-xN(x>0.4) utilizing surface treatment and optimized metallization scheme.
.
[OEDI-P-37] 张建宝,Improved Performance of GaN-Based Light-Emitting Diodes via AlInGaN/InGaN Electron-Emitting Layer
Abstract:
Improved performance of GaN-based light-emitting diodes (LEDs) using AlInGaN/ InGaN multiple quantum wells (MQWs) as an electron-emitting layer inserted between the active MQW region and n-GaN cladding layer has been demonstrated. Compared with the conventional electron emitting layer of GaN/InGaN MQWs, the light output power can be further enhanced by about 20%, while maintaining almost the same forward voltage. As the injection current increases, the external quantum efficiency of LEDs with the AlInGaN/InGaN MQW electron emitting layer exhibits a smaller efficiency droop. In addition, the negative electrostatic discharge endurance voltage of LEDs with the AlInGaN/InGaN MQW electron emitting layer is significantly higher.
.
[OEDI-P-38] 邹冰融,All-optical parallel NRZ-QPSK to RZ-QPSK format conversions Based on a Single SOA
Abstract:
All-optical format conversion is a key function in providing flexible management and interface for optical networks with different formats. In this paper, we propose and demonstrate multi-channel format conversions from the non-return-to-zero quadrature-phase-shift-keying (NRZ-QPSK) to the return-to-zero QPSK (RZ-QPSK) signals using a single semiconductor optical amplifier (SOA) and a delay interferometer (DI). The conversion from the NRZ-QPSK to RZ-QPSK is based on the cross phase modulation (XPM) effect, which is introduced by a synchronous optical clock signal with high input power, and subsequent detuned filtering. The amplitude of the NRZ-QPSK signal is converted to the RZ-QPSK signal with identical phase shift onto every input bit by the XPM effect. Parallel 4 channels format conversions from the NRZ-QPSK to the RZ-QPSK signals are experimentally achieved well with small Q penalty less than 2 dB.
[OEDI-P-39] 陈庆庆,A feasible method of growing low density InAs/GaAs QDs on Ge substrate by MOCVD
Abstract:
In this study, we found that InAs QDs density decreased with a higher V/III ratio within a certain extent. Considering the results and the former work in our group, we proposed a feasible method of growing low density InAs/GaAs QDs on Ge substrate by MOCVD.